Hello, I’ve used LinuxLive USB Creator and VirtualBox. I choose “install – start the installer directly” the reaver-iso starts loading, but both passwords are invalid. Username: reaver (or tech) Password: reaver (or tech) What have I forgotten. What is this “kernel” thing Thanks, Newbie Additional info: Win7 / AWUS036NH
Booting from USB works fine, Ubuntu wireless manager can see networks, but starting Reaver to scan shows no networks at all Does this only show WPS enabled networks?
Might have to do a bit of digging at the start of the thread for a solution Shows all networks but only WPS you can attack with. Check the first page for interface screenshots.
Thanks, I`ll do some reading --- Double Post Merged, 29 Mar 2013, Original Post Date: 27 Mar 2013 --- Worked a treat thanks, busy cracking my BT HH3.0 atm 2 seconds/pin on my laptop --- Double Post Merged, 29 Mar 2013 --- Watching Reaver coming towards the end of its attack, my WPS PIN starts 9046xxxx Reaver starts from low numbers and ends with high, would there be a way to start 2 Reaver attack sessions, one starting from 0xxxxxxx counting up, and the other starting from 9xxxxxx and counting down? Basically cutting the attack time in half at the least, or in my case, an almost immediate success coming from the session starting at 9xxxxxxx ? EDIT - It took my laptop 6h25m to crack the BT HomeHub 3.0 It found the pin at 93.95%
yes you can..but u must use terminal....or minidwep and inflator....when use minidwep/terminal/inflator when click reaver put this command Code: Select All reaver -i mon0 -b XX:XX:XX:XX:XX:XX -p 90000000 -v
I found out what I did wrong. During LinuxLive installation I didn't use the Reaver-iso file, but a clean newly downladed Ububtu file. I now installed linuxLive again and Reaver loaded with no problems. I started modzilla firefox and started the Reaver survey. But no networks are identified. Ill take a look at it tomorrow. Thanks
Greeting to all of you my brother hackers ! First of all sorry for may English,its not good I know I have a problem with reaver.I have about 10 APs which I can hack with Reaver. Succesfully hacked 2 of them,but with all the rest APs reaver starts hacking them and after 0,1% its just start to send identity response over and over and the APs go to lock state.After that nothing helps,except if owner reset the router.Situation is same with all the APs,its start sending pins and when it comes to 0.1% APs lock themselves. Im using TPlink 722nc wireless adapter,windows 7 and vmware workstation.Card is in monitor mode and support injection.Signal is excelent and in the first 0.1% reaver tries pins and everything goes perfect(no warning messeges,transaction codes or something similar) after that aps lock themselfes. I tryed next commands : reaver -i mon0 -c 11 -b 00:01:02:03:04:05 -vv reaver -i mon0 -c 11 -b 00:01:02:03:04:05 -vv -x 60 reaver -i mon0 -c 11 -b 00:01:02:03:04:05 -vv -S -N reaver -i mon0 -c 11 -b 00:01:02:03:04:05 -vv -S -N -L -d 15 -r 3:15 -T .5 -x 360 reaver -i mon0 -c 11 -b 00:01:02:03:04:05 -vv -S -N -L -d 5 -r 3:5 -T .5 -x 360 reaver -i mon0 -c 11 -b 00:01:02:03:04:05 -vv -S -N -L -d 60 -r 3:15 -T .5 -x 360 reaver -i mon0 -c 11 -b 00:01:02:03:04:05 -vv -S -N -L -d 60 -r 3:61 -T .5 -x 360 After 0.1% this what the reaver says : Sending identity response Received identity request Sending identity response Received identity request Sending identity response Received identity request Sending identity response Received identity request Sending identity response Received identity request Sending identity response [!] WPS transaction failed (code: 0x02), re-trying last pin Simply APs locks themselfs. My question is :whats the problem is?
I bet you those routers are made by linksys. These are the only ones that lock themselves when used with reaver. Can you check the MAC address on the ones that lock? See here: http://hwaddress.com/?q=linksys
May I ask what are the first six characters of the AP's BSSID?..that tells alot..each vendor configures their products differently..or is that the BSSID it shows? Motorola has a feature to fake/spoof it's MAC...also, did you change the MAC of your virtual interface? (mon0) Some claim to get better results by using their physical interface simply by using this command: Code: Select All iwconfig wlan0 Mode Monitor and not changing the MAC...which is the actual way Reaver was designed to work...https://code.google.com/p/reaver-wps/wiki/FAQ but it's up to you..
Tactical Network Solutions have hinted after one of their followers tweeted about the kit and the price. Funny they avoided talking about the price. Anyway, by the looks of it there will be another iteration of Reaver Pro. What will it be? who knows. Hopefully it will be a lot better than what they have had in the past and a bit cheaper too. Currently you cannot buy the Reaver Pro kit as the distributor Hak5 is out of stock. @djkevster we are working on the next iteration. The design will be different and will include a software update. Stay tuned!— TacNetSol (@tacnetsol) April 15, 2013
hi i am using reaver pro from my usb . Iam using airlive wl1700 usb . i run reaver pro and anyting is fine and when i start the attack he is trying 12345670 -.- how can i fix this --- Double Post Merged, 13 Sep 2013, Original Post Date: 13 Sep 2013 --- i have a problem whit reaver pro he is always trying the same pin
I thought the same thing a few days ago when I downloaded it, I tried all different combinations of passwords and none of them worked Then out of frustration I tried the xiaopanforums password again making sure to copy / paste it perfectly without spaces and this time it worked, I have no idea what was wrong, but that is 100% the correct password Uploaded the extracted ISO Code: Select All https://mega.co.nz/#!F9pgiIqL!KMgppTPq5CS2Qw4r8kL1GAcyV0YvTpKmqVzjlt9PxYc
Ok your right!...IDK how it worked this time but that's exactly what I was putting in the first few hundred times....Anyway I been watching how everyone has been using this app and make wifi cracking look so easy....hope it works for me too! I'll keep you posted on my experience!
Hi, I am sorry but I can't seem to find my answer anywhere. Does reaver pro have several versions like 1.0 or 1.3 or 2.4? Thank you msramalho --- Double Post Merged, 4 Nov 2013, Original Post Date: 4 Nov 2013 --- Hello,
