now i see, this is the first problem i get when using reaver....................it ok just let it like that, maybe a day cause if u use -vv command it much slower...but now u can use reaver
Why are you not in monitor mode? that is probably why it is not working! Should be mon0 not wlan0, put your card in monitor mode when you start inflator. I am calling this issue fixed until further notice. -vv just shows you detailed errors, no impact on performance.
are u sure Mr. Penguin, cause when i using the vv command it take me one and half day to crack it but without the vv command only took 3hours
it the same ap's...it try pin after a lot of sending m4 and m3 message.....................after that try pin again
Using Xiaopan_0.4.2.3 on my rt8187l > can't detect APs even some are around me unless using (-C) > need to unplug and plug again my usb adapter each time I'm done with VMware > failed to associate unless using (-A) So I tried lower version using Xiaopan_0.4.2.1 on my rt8187l target same AP > detected AP using default command > no need to unplug and plug after using VMware > easily associated and started trying pin with progress....bravo!! Damn, I stayed back in my office for extra hours just to try this.......but its satisfying and kudos to whoever invented and improve it over time..my special thanks to Bro Crackerz Wave and Mr.Peguin for their time and patience
Well that is what monitor (mon0) mode does, it works. normal mode (wlan0) does not. I bet that was the issue, give it time to change into monitor mode next time. RTL8187L is aways compatible with Xiaopan, no matter what version.
Hi, I am using XIAOPAN 0.4.2.1, SINMAX RTL8187, Run in VMware. For my case, i did wait for it change to monitor mode as per 1st image as follows, but still my Aps RSSI are all "00" in 2nd image. How can i get the RSSI value in order to identify the best signal strength network before i proceed? thank you
It's not going to work in wlan0. You have not addressed the issue. Your card is not going into monitor mode which is required for a successful Reaver attack and is why you are getting 00 RSSI. Sent from my iPhone using Tapatalk
Hi, As i proceed, seems it had switch back to wlan0 mode instead of mon0, please guide me on this. Please advise does the following not meaning it was succeeded to went into Monitor mode?
I have never got that issue before. So I do not know how to fix it. Maybe a reboot and try again might work. For a workaround: Type the following in RootShell: Code: Select All airmon-ng start wlan0 This will get your card into monitor mode If you want to search for WPS enabled networks enter the following: Code: Select All wash -i mon0 Or if you just want to see all the networks around you enter the following: Code: Select All airodump-ng wlan0 Then check it with the following: Code: Select All iwconfig Copy the attack command you see in the inflator image and paste it into RootShell and push enter (Remember to change wlan0 to mon0 and instead of -v use -vv [for detailed errors])
It is great your card is in monitor mode. Failed to open mon0 for capturing can be resolved with the following: Try adding sudo to the front of wash. E.g: Code: Select All sudo wash -i mon0 In future please do not quote entire posts. Only some parts, when appropriate: It has already been mentioned and it is difficult for people to find useful non bloated information.
Sometimes I have the same problem where card won't get into monitor mode as in picture. Open up a terminal and key as Mr.Penguin suggested " sudo airmon-ng start wlan0". Then I run inflator and the card would be on monitor mode. Kentck86, try this. Reboot your Xiaopan, look for this folder My Document\My Virtual Machine\ "Xiaopan 0.4.1" or whatever name you have given it. Delete the whole folder then run Vmware again to create a new "Xiaopan' Hope this helps.
Kent, Is your card connected? Check before you run "rfkill list" You should get this as in pic kentck86, One more last thing before I go, run xiaopan using live usb. It gives you less error. Cheers!! Take a look here http://unetbootin.sourceforge.net/
No result return to me by executing sudo rfkill list in terminal, the card is connected well. btw, i am running xiaopan 0.4.2.2.
